VW Passat repair


+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines of configuration of R4
   + 3.2. Petrol engine of configuration of VR6
   - 3.3. Diesel engines
      3.3.1. Technical characteristics
      3.3.2. General information
      3.3.3. Installation of the piston of the cylinder No. 1 in VMT
      3.3.4. Compression check in cylinders
      3.3.5. Gear belt of a drive of GRM
      3.3.6. Mechanism of a tension of a gear belt
      3.3.7. Gear pulley of a camshaft
      3.3.8. Gear pulley of a cranked shaft
      3.3.9. Pulley of an intermediate shaft
      3.3.10. Belts of a drive of auxiliary units
      3.3.11. Cover of a head of the block of cylinders
      3.3.12. Replacement of an epiploon of a camshaft
      3.3.13. Replacement of an epiploon of an intermediate shaft
      3.3.14. Replacement of epiploons of a cranked shaft
      3.3.15. Replacement of an epiploon of a forward cover of a cranked shaft
      3.3.16. Head of the block of cylinders
      3.3.17. Check of work of hydraulic pushers
      3.3.18. Flywheel
      3.3.19. Replacement of support of the power unit
      3.3.20. Oil case
      3.3.21. Oil pump
      3.3.22. Top casing of the AFN engine
      3.3.23. System of prestarting heating of diesel engines
      3.3.24. Glow plugs
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Drive of forward wheels
+ 10. Suspension brackets
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
+ 15. Electric equipment
+ 16. Body
+ 17. Electric circuits


Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Engines>> Diesel engines>> Replacement of an epiploon of a camshaft
Removal of an epiploon of a camshaft carry out in the following order:
– on the AFN engine remove the top casing of the engine;
– disconnect the tip from the electromagnetic valve of a stop of the engine;
– remove auxiliary driving belts;
– remove pulleys of auxiliary driving belts and an external casing of a GRM belt;
– establish the piston of the first cylinder in situation VMT and remove a GRM belt;
– if it is established, remove the mechanism of a tension of a GRM belt and a camshaft pulley;
– отверините screws also remove an internal casing of a GRM belt established on the block of cylinders;
– uncover gochlovka of the block of cylinders (see section 3.3.10);

Fig. 3.68. Head of the block of cylinders: 1–a head of the block of cylinders, 2 – laying of a head of the block of cylinders, 3 – the directing plug of the valve, 4 – a forward cover of the bearing of a camshaft, 5 – a bolt of fastening of a head of the block of cylinders, 6 – a maslootrazhatelny plate, 7 – laying of a cover of a head of the block of cylinders, 8 – a cover of a head of the block of cylinders, 9 – a plate, 10 – a stopper of a maslonalivny mouth, 11 – the union of the valve of a regulator of ventilation of a case


– отверините two nuts also remove a forward cover 4 bearings of a camshaft (see fig. 3.68 );
– take a camshaft epiploon.
Installation of an epiploon of a camshaft carry out in the following order:
grease a new epiploon of a camshaft with pure engine oil and establish to the place of the removed;
apply a thin film hermetic on interfaced surfaces of a forward cover of the bearing of a camshaft, then establish a cover on a head of the block of cylinders and wrap nuts the demanded moment;
establish a cover of a head of the block of cylinders;
establish an internal casing of a gear belt and pulleys;
establish a GRM belt and adjust its tension;
establish an external casing of a GRM belt;
establish auxiliary driving belts and adjust their tension.