VW Passat repair+ 1. Ekspluatatsiiya of the car + 2. Maintenance - 3. Engines + 3.1. Petrol engines of configuration of R4 + 3.2. Petrol engine of configuration of VR6 - 3.3. Diesel engines 3.3.1. Technical characteristics 3.3.2. General information 3.3.3. Installation of the piston of the cylinder No. 1 in VMT 3.3.4. Compression check in cylinders 3.3.5. Gear belt of a drive of GRM 3.3.6. Mechanism of a tension of a gear belt 3.3.7. Gear pulley of a camshaft 3.3.8. Gear pulley of a cranked shaft 3.3.9. Pulley of an intermediate shaft 3.3.10. Belts of a drive of auxiliary units 3.3.11. Cover of a head of the block of cylinders 3.3.12. Replacement of an epiploon of a camshaft 3.3.13. Replacement of an epiploon of an intermediate shaft 3.3.14. Replacement of epiploons of a cranked shaft 3.3.15. Replacement of an epiploon of a forward cover of a cranked shaft 3.3.16. Head of the block of cylinders 3.3.17. Check of work of hydraulic pushers 3.3.18. Flywheel 3.3.19. Replacement of support of the power unit 3.3.20. Oil case 3.3.21. Oil pump 3.3.22. Top casing of the AFN engine 3.3.23. System of prestarting heating of diesel engines 3.3.24. Glow plugs + 4. Cooling system + 5. Power supply system + 6. Ignition system + 7. Coupling + 8. Transmission + 9. Drive of forward wheels + 10. Suspension brackets + 11. Steering + 12. Brake system + 13. Wheels and tires + 14. Systems of heating, ventilation and conditioning + 15. Electric equipment + 16. Body + 17. Electric circuits 
|
Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Engines>> Diesel engines>> Replacement of support of the power unit
Removal and installation of a forward support of the engine carry out in the following order:
– disconnect a wire from the negative plug of the storage battery;
– establish under the engine a jack and through wooden whetstone raise a jack the engine so that the weight of the engine was perceived by a jack;
– turn out a bolt of fastening 3
(fig. 3.72)
of a forward support 2 engines;
– remove a starter;
– unscrew bolts of 4 fastenings of a forward support 2 to the power unit and remove an arm;
– turn out a bolt of the 5th fastening of a support of the engine to a forward beam;
– remove a forward support of the engine;
– installation of the removed elements make in sequence, return to removal.
Tighten all bolts of fastening of a support of the power unit the demanded moment according to technical characteristics.
Removal and installation of a back right support of the engine carry out in the following order:
– disconnect a wire from the negative plug of the storage battery;
– fix the engine slings of the load-lifting mechanism (winch) and raise so that the weight of the engine was perceived by the load-lifting mechanism;
– turn out a coupling bolt 9 (see
fig. 3.72
) the right back support of the 8th engine;
– unscrew bolts of 1 fastening of an arm of the right back support of the engine to the block of cylinders;
– unscrew bolts of fastening of a back right support of the engine to a body and take a support from a motor compartment;
– installation of the removed elements make in sequence, return to removal;
– tighten all bolts of fastening of a back right support of the engine the demanded moment according to technical requirements.
Removal and installation of a back left support of the engine carry out in the following order:
– disconnect a wire from the negative plug of the storage battery;
– establish under the engine a jack and through wooden whetstone raise a jack the engine so that the weight of the engine was perceived by a jack;
– turn out a bolt of the 7th fastening of a support of the 6th engine;
– turn out a bolt of fastening of a back left support of the engine to a transmission.
– turn out bolts of fastening of an arm of a support of the engine to a body and take a support from a motor compartment;
– installation of the removed elements make in sequence, return to removal.
|
|