VW Passat repair


+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Drive of forward wheels
+ 10. Suspension brackets
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
+ 15. Electric equipment
- 16. Body
   + 16.1. General information
   16.2. Care of a body
   + 16.3. Insignificant damages of a body
   16.4. Considerable damages of a body
   16.5. Moldings, facing of wheel niches
   + 16.6. Cowl elements
   16.7. Forward and back bumpers
   16.8. Forward cross-section beam of a body
   16.9. Forward wing
   + 16.10. Luggage carrier elements
   + 16.11. Elements of a back door (cars with a body the versatile person)
   16.12. Hinges and locks
   16.13. Elimination of jingle of doors
   - 16.14. Elements of a forward door
      16.14.1. Internal furnish of a forward door
      16.14.2. Window regulator
      16.14.3. Glass of a forward door
      16.15.4. Window regulator electric motor
      16.14.5. Lateral rear-view mirrors
      16.14.6. Handle, locks and clamps of locks of a forward door
      16.14.7. Forward door assembled
      16.14.8. Sealant of a forward door
   + 16.15. Elements of a back door
   16.16. Internal rear-view mirror
   16.17. Central console
   + 16.18. Combination of devices
   16.19. The receiver with coding system
   16.20. Perchatochny box
   16.21. Dashboard
   + 16.22. Forward seats
   + 16.23. Back sitting
   + 16.24. Seat belts
+ 17. Electric circuits


Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Body>> Elements of a forward door>> Internal furnish of a forward door
Removal make in the following order:

Fig. 16.23a. Internal furnish of a forward door on early models: 1–protective water insulating film; 2–nut; 3– bracket; 4–the handle for door closing from within; 5–overlay of the internal door handle; 6–decorative plate; 7–decorative panel; 8–button of blocking of the door lock; 9–a bracket of the button of locking (it is pressed inside); 10-clamp of the decorative panel


– turn on and remove the button of blocking 8 (fig. 16.23a or 16.23b) of the door lock;
– remove the furnish panel;
– remove a decorative plate (fastens on latches cave-in);

Fig. 16.24. Removal of the handle of a window regulator: 1–slip; corner а=45 (±12) °


– on a door with window regulators with a manual drive, remove a slip in the arrow direction from the window regulator handle, unscrew the fixing screw and remove the handle (fig. 16.24) ;
– take the intermediate plug;.
– accurately remove furnish from the internal handle of closing of a door then unscrew two screws of fastening and remove the handle;

Fig. 16.25. Removal of an overlay of the internal handle


– remove an overlay of furnish of the internal handle of opening of a door for what slightly pull the handle on itself, hook a slip and displace it to a back part of a door (fig. 16.25) ;
– remove a control lever an external mirror;
– unscrew screws of fastening of internal furnish of a door, take internal furnish from a groove of consolidation of glass, then lift and remove it from a door;

Fig. 16.23b. Internal furnish of a forward door on later models: 1–cap or high-frequency loudspeaker; 2–decorative overlay of the internal handle; 3–handle; 4, 5, 7, 12 – the screw; 6–decorative slip; 8–button of blocking of the door lock; 9–bracket of the button of locking; 10-bracket; 11-bracket; 13-decorative panel; 14-rubber furnish; 15-pocket; 16-loudspeaker lattice; 17-window regulator handle


– having unscrewed fixing screws, remove a pocket 15 (see fig. 16.23b ) doors;
– if necessary disconnect wires from a loudspeaker;
– for removal of a protective water insulating film take the compressed pins and remove brackets;
– remove remote control by the door lock and disconnect draft of the lock;
– accurately turn on and remove from a door a protective water insulating film.
Installation carry out to sequences, return to removal.
Replace the brackets broken at removal.
Check correctness of connection of electric sockets.
At installation of the handle of a window regulator it is necessary to sustain its situation according to fig. 16.24 (the corner "and" it should be equal 45 ° ± 12 °), the window should be thus completely closed.