VW Passat repair


+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Drive of forward wheels
+ 10. Suspension brackets
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
+ 15. Electric equipment
- 16. Body
   + 16.1. General information
   16.2. Care of a body
   + 16.3. Insignificant damages of a body
   16.4. Considerable damages of a body
   16.5. Moldings, facing of wheel niches
   + 16.6. Cowl elements
   16.7. Forward and back bumpers
   16.8. Forward cross-section beam of a body
   16.9. Forward wing
   + 16.10. Luggage carrier elements
   + 16.11. Elements of a back door (cars with a body the versatile person)
   16.12. Hinges and locks
   16.13. Elimination of jingle of doors
   + 16.14. Elements of a forward door
   + 16.15. Elements of a back door
   16.16. Internal rear-view mirror
   16.17. Central console
   - 16.18. Combination of devices
      16.18.1. Removal and installation
   16.19. The receiver with coding system
   16.20. Perchatochny box
   16.21. Dashboard
   + 16.22. Forward seats
   + 16.23. Back sitting
   + 16.24. Seat belts
+ 17. Electric circuits


Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Body>> Combination of devices>> Removal and installation
Removal make in the following order:
– disconnect a "minus" wire from the plug of the storage battery;
– remove a steering wheel.

Early models

Fig. 16.62. Screws (are specified by shooters) fastenings of an overlay of a combination of devices: and — on early models; — on later models


Having unscrewed two screws, remove a decorative overlay of a combination of devices (fig. 16.62) ;
– unscrew screws and remove a combination of devices.

Later models
Remove three lattices of system of ventilation from the driver and in the center;
– remove the rotary switch of lighting;
– remove furnish behind the left side of a steering wheel;
– unscrew four screws — on one behind each lattice of ventilation and one behind furnish — and remove a decorative overlay of a combination of devices ( fig. 16.62 , and);

All models

Fig. 16.63. Two screws (2) fastenings of a cover of a combination of devices to the case and two screws (1) fastening of a combination of devices assembled


To Overnita screws, carefully disconnect a speedometer cable, conducting sockets, if necessary disconnect a vacuum hose from the multipurpose indicator and remove a combination of devices (fig. 16.63) ;

Fig. 16.64. Removal and installation of devices from a combination of devices on cars of an early model range: 1–index of level of fuel; 2–speedometer; 3–tachometer; 4–pin; 5–fastening screw


– remove devices on cars of early models, as is shown in fig. 16.64 . To remove the index of 1 level of fuel and a tachometer 3 get pins 4. Get the index, having disconnected it from sockets of the case and the printed-circuit board. to remove a speedometer 2 unscrew screws of fastening 5;

Fig. 16.65. Removal and installation of devices from a combination of devices on cars of later models: 1–the index of level of fuel and temperature of cooling liquid; 2–speedometer; 3–tachometer; 4–screw


– remove devices on cars of late models, as is shown in fig. 16.65 . To remove the index of 1 level of fuel and temperature of cooling liquid or a tachometer 3, it is necessary to take accurately them from sockets of the case and the printed-circuit board. To remove a mechanical speedometer unscrew screws 4 and carefully get a speedometer 2 from the case. To remove a speedometer with the electronic counter of the passable way it is necessary to get carefully it from the case and to remove from pins.
Devices can be removed without dismantle of the case of a combination of devices.

Fig. 16.66. Details of a cable of a speedometer: 1–spring case; 2–cable; 3–sealant


Connection of a cable of a speedometer is carried out according to fig. 16.66 . The cable is entered into a speedometer from the back party. Fixing of a cable of a speedometer is provided with the spring which has been built in in a cover of a cable.
Installation of a combination of devices carry out to sequences, return to removal.