VW Passat repair


+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
- 9. Drive of forward wheels
   9.1. General information
   9.2. Check of antisplash covers
   9.3. Removal and installation of a drive of forward wheels
   9.4. Removal and installation of the internal hinge
   9.5. Removal and installation of the external hinge
   9.6. Dismantling of the external hinge
   9.7. Dismantling of the internal hinge
   9.8. Quencher of krutilny fluctuations of a power shaft
   9.9. Epiploon of a flange of a semi-axis
   9.10. Malfunctions of power shafts
+ 10. Suspension brackets
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
+ 15. Electric equipment
+ 16. Body
+ 17. Electric circuits


429b39f6





Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Drive of forward wheels>> Removal and installation of a drive of forward wheels

Fig. 9.1. Drive of forward wheels: 1–lock ring; 2–special laying; 3–internal hinge; 4–washer; 5–protective cover; 6–protective casing; 7–bolt; 8–power shaft; 9–small collar; 10-protective cover; 11-big collar; 12-tarelchaty washer; 13-washer; 14-lock ring; 15-external hinge; 16-cylindrical pin; 17-a quencher of krutilny fluctuations (from two parts); 18-bolt; 19-plate


Removal of a drive of forward wheels carry out in the following order:
– tighten the lever of the parking brake and remove a decorative cap from the corresponding forward wheel;
– weaken a nut of fastening of a power shaft and bolts of fastening of a wheel;
– will hang out and fix on basic racks a forward part of the car;
– having unscrewed bolts of fastening of a wheel, remove a wheel;
– unscrew a nut of fastening of a power shaft and remove it together with laying;
– for removal of the left power shaft unscrew a rotary fist from an amortization rack. Bolts of fastening of a rotary fist establish a corner of disorder of forward wheels therefore before an otvorachivaniye, it is necessary to mark out the provision of bolts for correct installation them in the same situation. Adjustment of a corner of disorder of forward wheels needs use of the special equipment;
– for access to the right internal hinge of a power shaft unscrew and remove a counterbalance from the bottom frame of a steering and protection of the hinge;
– using a many-sided face head of 8 mm, unscrew bolts of fastening of flanges of power shafts on a transmission;
– disconnect a power shaft from a transmission and lift it;
– a stripper squeeze out a power shaft from a wheel nave. Pay attention: the internal end of a power shaft should settle down over a transmission as at expression of a power shaft it is displaced inside and can rest against a transmission. If necessary disconnect steering draft from a rotary fist and the stabilizer of cross-section stability from the cross-section lever of a suspension bracket;
– take a drive shaft from a rotary fist, at the same time tightening a car wheel outside;
– after removal of a drive of wheels from the car, do not lower the car on the earth and do not move it because of danger of damage of the bearing of a nave.
Installation of a drive of forward wheels carry out in the following order:
– before installation clear shlitsa and interfaced surfaces on the internal and external end of a power shaft. Clear shlitsa in a wheel nave;
– combine shlitsa and insert a power shaft into a wheel nave;
– establish new laying on an internal part of a power shaft;
– fill with greasing a cavity of the internal hinge, then establish a power shaft on a transmission flange, establish plates and bolts and tighten bolts the demanded moment;
– establish protection of the hinge and a counterbalance;
– at installation of the left shaft connect an amortizatorny rack to a rotary fist. Establish bolts in situation in which they were before removal, and tighten them the regulated moment;
– establish laying and turn, without tightening, a nut of fastening of a power shaft to a nave;
– having established a wheel, wrap bolts of fastening of a wheel and lower the car on the earth;
– finally tighten a nut of fastening of a power shaft to a nave and bolts of fastening of a wheel. Establish on a wheel a decorative cap.