VW Passat repair


+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Drive of forward wheels
+ 10. Suspension brackets
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
- 15. Electric equipment
   + 15.1. Technical characteristics
   15.2. Security measures at work with electric equipment
   + 15.3. Detection of not closed chain
   + 15.4. Storage battery
   - 15.5. Generator
      15.5.1. Security measures at work with the generator
      15.5.2. Generator check
      15.5.3. Main malfunctions of the generator and ways of their elimination
      15.5.4. Belt of a drive of the generator
      15.5.5. Generator brushes
      15.5.6. Check of system of start-up of the engine
   + 15.6. Starter
   15.7. Block of safety locks and relay
   15.8. Replacement of the lock of ignition
   + 15.9. Switches
   + 15.10. Combination of devices
   + 15.11. Internal lighting and lighter
   + 15.12. Headlights
   + 15.13. Windscreen cleaner
   15.14. Windscreen washers
   15.15. Cleaner of back glass
   + 15.16. Central lock
   + 15.17. Hatch
+ 16. Body
+ 17. Electric circuits


429b39f6





Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Electric equipment>> Generator>> Belt of a drive of the generator
Removal
Removal make in the following order:
– disconnect a "minus" wire from the plug of the storage battery;

       PREVENTION
Information in memory of electronic memories will be thus lost.


Fig. 15.6. Arrangement of an adjusting nut and bolt of the mechanism of a tension of a driving belt of the generator: 1–bolt; 2–adjusting nut


– weaken a bolt of fastening of the generator to an arm and a bolt of adjustment of a tension of a belt (fig. 15.6) , then turn the generator to the engine;
– on the cars equipped with the conditioner and a steering drive with the amplifier, first of all remove their driving belts;
– remove a driving belt from pulleys.

Installation and tension adjustment
Establish a new driving belt on pulleys, thus a belt should settle down on the center of pulleys.
The tension of a driving belt can be made in two ways.

Fig. 15.7. Places of check of a tension of a driving belt (it is shown by an arrow): 1–pulley of a drive of the generator; 2–belt; 3–a pulley of the pump of cooling liquid; 4–pulley of a cranked shaft


Fig. 15.8. Places of check of a tension of driving belts with the amplifier of a steering (it is shown by shooters): 1–pulley of a drive of the generator; 2–belt of a drive of the generator; 3–a pulley of the pump of cooling liquid; 4–belt of a drive of the pump of the amplifier of a steering; 5–pulley of the pump of the amplifier of a steering; 6–pulley of a cranked shaft


Fig. 15.9. Places of check of a tension of driving belts with the conditioner (it is shown by shooters): 1–pulley of a drive of the generator; 2–belt of a drive of the generator; 3–pulley of the compressor of the conditioner; 4–belt of a drive of the compressor of the conditioner; 5–a pulley of the pump of cooling liquid; 6–pulley of a cranked shaft


Fig. 15.10. Places of check of a tension of driving belts with the amplifier of a steering and (arrow) conditioner: 1–pulley of a drive of the generator; 2–belt of a drive of the generator; 3–pulley of the compressor of the conditioner; 4–belt of a drive of the compressor of the conditioner; 5-a pulley of the pump of cooling liquid, 6 – a belt of a drive of the pump of the amplifier of a steering; 7–pulley of the pump of the amplifier of a steering; 8–pulley of a cranked shaft


Fig. 15.11. Check of a tension of a driving belt of the generator


Fig. 15.12. Fixing of a nut and bolt of the mechanism of a tension of a driving belt of the generator


In the first case weaken an adjusting bolt and rotate a nut of the mechanism of a tension so that the generator moved from the engine while the deflection of a driving belt on the middle of a long branch of a belt will not make 2,0 mm when pressing by a thumb – for a new belt and 5,0 mm – for a belt being in the use (fig. 15.7, 15.8, 15.9, 15.10, 15.11) . Fix a nut of the mechanism of a tension in this situation then tighten an adjusting bolt (fig. 15.12) .
At a belt tension by the second way the dinamometrichesky key is required. Check, that the bolt of fastening of the generator to an arm was weakened, and the generator freely moved. Tighten a nut of the mechanism of a tension the moment of 8 N · m for a new belt (or 4 N · m for a belt which was in the use), then note position of the generator on an adjusting level. Tighten a bolt of fastening of the generator to an arm and check, that the nut of the mechanism of a tension remained in the same situation.
In case of need, carry out repeated adjustment.
Tighten an adjusting bolt.