VW Passat repair


+ 1. Ekspluatatsiiya of the car
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines of configuration of R4
   - 3.2. Petrol engine of configuration of VR6
      3.2.1. Technical characteristics
      3.2.2. General information
      3.2.3. Check of a technical condition of the engine
      3.2.4. Removal and engine installation
      3.2.5. Removal and installation of a head of the block of cylinders
      3.2.6. Repair of a head of the block of cylinders
      3.2.7. Pistons and rods
      3.2.8. Cranked shaft
      3.2.9. Replacement of epiploons of a cranked shaft
      3.2.10. Flywheel
      3.2.11. Drive of the gas-distributing mechanism
      3.2.12. Intermediate shaft
      3.2.13. Removal and installation of the oil pallet
      3.2.14. Oil pump
      3.2.15. Water pump
   + 3.3. Diesel engines
+ 4. Cooling system
+ 5. Power supply system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Drive of forward wheels
+ 10. Suspension brackets
+ 11. Steering
+ 12. Brake system
+ 13. Wheels and tires
+ 14. Systems of heating, ventilation and conditioning
+ 15. Electric equipment
+ 16. Body
+ 17. Electric circuits


429b39f6





Repair B3-B4/Passat B3-B4 Volkswagen Passat>> Engines>> Petrol engine of configuration of VR6>> Drive of the gas-distributing mechanism

Fig. 3.56. GRM drive: 1–intermediate shaft; 2–asterisks of camshafts; 3–chain of a drive of camshafts; 4–axis of a boot of a natyazhitel of a chain of a drive of camshafts; 5–boot of a natyazhitel of a chain of a drive of camshafts; 6–natyazhitel of a chain of a drive of camshafts; 7–a conducted asterisk of an intermediate shaft; 8–leading asterisk of a drive of camshafts; 9–bolt of fastening of asterisks of an intermediate shaft; 10-natyazhitel of a chain of a drive of an intermediate shaft; 11-bolt of fastening of a natyazhitel of a chain of a drive of an intermediate shaft; 12-cranked shaft; 13-chain of a drive of an intermediate shaft; 14-uspokoitel of a chain of a drive of an intermediate shaft; 15-fingers of an uspokoitel of a chain of a drive of an intermediate shaft; 16-uspokoitel of a chain of a drive of camshafts; 17-bolt of fastening of an asterisk of a camshaft; 18-coupling of a drive of the distributor of ignition


The drive of camshafts is carried out from a cranked shaft by means of chain transfers through an intermediate shaft (fig. 3.56) . The tension of a chain 3 drives of camshafts is regulated by a bolt 6. The hydraulic natyazhitel of 10 chains of an intermediate shaft automatically establishes its tension.
Removal of a drive of GRM is carried out in the following order:

Fig. 3.57. Combination of labels of installation of the piston of the cylinder No. 1 in VMT: 1–chain of a drive of camshafts; 2–asterisk of an intermediate shaft; 3–asterisk of an intermediate shaft leader of a drive of camshafts; 4–chain of a drive of an intermediate shaft; 5–natyazhitel of a chain of a drive of an intermediate shaft; 6–clamp of a natyazhitel of a chain of a drive of an intermediate shaft; 7–asterisk of a cranked shaft; 8–uspokoitel of a chain of a drive of an intermediate shaft; 9–adjusting labels of VMT; 10-bolt of fastening of asterisks of an intermediate shaft


– establish the cylinder No. 1 piston in VMT of a step of compression, for this purpose turn a cranked shaft clockwise before combination of adjusting labels (fig. 3.57) ;
– weaken a tension of a chain 3 (see fig. 3.56 ) a drive of camshafts, for this purpose turn out a bolt 6 natyazhitel of a chain;
– put labels with paint on a chain of a drive of camshafts in the places shown on fig. 3.57 ;
– block a cranked shaft from a provorachivaniye;

Fig. 3.58. Oil pump and oil filter: 1–index of level of engine oil; 2–block of cylinders; 3–cover of a shaft of a drive of the oil pump; 4–gear wheel of a drive of the oil pump; 5–intermediate shaft; 6–cover of an intermediate shaft; 7–asterisk of an intermediate shaft; 8–asterisk of an intermediate shaft of a drive of camshafts; 9–bolt of fastening of asterisks of an intermediate shaft; 10-shaft of a drive of the oil pump; 11-oil pump; 12-bolt of fastening of the oil pump; 13-laying of a maslopriyemny pipe; 14, 16 – bolts of fastening of a maslopriyemny pipe; 15-maslopriyemny pipe; 17-cover of the oil filter; 18-sealing ring; 19-oil filter; 20-case of the oil filter; 21-bolts of fastening of the case of the oil filter


– unscrew a bolt of the 9th fastening of asterisks of an intermediate shaft and remove an asterisk 8 (see fig. 3.58 );
– remove a chain 3 drives of camshafts;
– remove an asterisk 7 intermediate shaft;
– remove a chain 4 drives of an intermediate shaft. (see fig. 3.57 ).

       PREVENTION
Do not turn a cranked shaft after removal of chains of a drive of GRM. It will lead to blow of pistons about valves.

Installation of a drive of GRM is carried out in the following order:
– check installation of the piston of the cylinder No. 1 in VMT, thus short tooth of an asterisk 7 (see fig. 3.57 ) a camshaft it should be combined with an adjusting label 9 on a forward cover of a cranked shaft;
– establish a chain 4 drives of an intermediate shaft on an asterisk 7 cranked shaft;
– establish a chain 4 on an asterisk 2 intermediate shaft and establish an asterisk 2 on an intermediate shaft;
– check ledge combination on an asterisk 2 intermediate shaft with an adjusting label on a cover of an intermediate shaft;
– establish an asterisk 3 on an intermediate shaft and tighten a bolt of the 10th fastening of asterisks the moment of 100 N · m, having fixed from a provorachivaniye an intermediate shaft;
– establish directing 16 (see fig. 3.56 ) chains of a drive of camshafts;
– establish a head of the block of cylinders (see подразд. 3.2.5);
– be convinced that camshafts are established in the situation relevant to VMT of the piston of the cylinder No. 1;
– fix camshafts from a provorachivaniye;
– establish asterisks 2 on asterisk camshafts with the chain put on them 3;
– establish the coupling 18 of a drive of the distributor of ignition and wrap bolts of the 17th fastening of asterisks of camshafts;
– tighten bolts the 17th moment of 100 N · m, holding camshafts from a provorachivaniye a wrench;
– unblock the piston of a hydraulic natyazhitel of 5 chains of a drive of an intermediate shaft, having turned a clamp the 6th screw-driver;
– establish a natyazhitel 5 and tighten bolts of his fastening the moment of 20 N · m;
– check combination of all adjusting labels;
– unblock camshafts;
– execute other operations in sequence, return to removal.